FBX-SOLO Model SM820FBX-SOLO Model SL820QUICK START OPERATIONFor best results, read all operating instructionsbefore using the FBX-SOLO (pages 10-19).
10BEFORE YOU BEGIN...The FBX automatic feedback controller improves anysound reinforcement system. By following thesesimple instructions, you will be
11creased activity at one of those frequencies maycause the filter to go deeper (e.g.., deepen from -12dB to -15 dB). Activating the Lock Fix function
12TURBO MODE SETUPThe FBX-SOLO incorporates Turbo Mode setup,which is indicated by a flashing red Clip LED. Thislightning-quick setup feature cuts the
13same time, raise the system gain and set the FBXfilters one at a time.In some situations, raising the number of dynamicfilters (versus fixed FBX fil
14FBX SETUP INSTRUCTIONSPlace the speakers and micro-phones in the positions where theywill be used during the program.Avoid placing microphones direc
15Slowly raise the inputchannel level fader forthe channel being setuntil feedback occurs.The SOLO shouldquickly remove the feed-back.The first Filte
16HOW TO USE THE LOCK FIXED FEATUREIn certain situations the FBX may mistake music forfeedback and drive the fixed filters deeper thannecessary, like
17and the mic is turnedon. If it is less thanthe threshold, thenoise gate closes,and the mic is turnedoff.You can adjust yourSOLO to four differentthr
18TROUBLESHOOTING TIPSQ. Can I patch the SOLO SL820 after the mixer andbefore the power amp?A. Yes, but only in cases where just eight feedbackfilters
19Q. Why does my SOLO set filters when music isplayed through it?A. Make sure the FBX’s Turbo Mode has beenturned off before you program. Check the si
2CONGRATULATIONS!You now have the state-of-the-art in feedback con-trol. The Sabine FBX-SOLO gives you automaticreal-time feedback control for any cha
20PRODUCT SPECIFICATIONSFILTERSEight independent digital notch filters controlledautomatically from 40 Hz to 20 KHzFilter width: 1/10 octave, typical,
21*Below approximately 200 Hz the feedback filters becomeslightly wider to increase the capture speed of feedback andrumble at these low frequencies.*
22FCC STATEMENTWarning: Changes or modifications to this unit not expressly approved by the party responsible forcompliance could void the user's
23ONE-YEAR LIMITED WARRANTY:THIS LIMITED WARRANTY VALID ONLY WHEN PURCHASED AND REGISTERED IN THEUNITED STATES OR CANADA. ALL EXPORTED PRODUCTS ARE SU
Manufactured by: Sabine, Inc.13301 NW US Highway 441Alachua, Florida 32615-8544 USA+USA (386) 418-2000 • Fax: +USA (386) 418-2001 www.Sabine.com©
3THE BEST FEEDBACKCONTROLLERBefore the invention of the FBX, the most commondevice for controlling feedback was the 31-bandgraphic EQ. However, the
4FREQUENCY RESPONSE TEST: Full Set-Up FBXvs. 1/3-Octave Graphic Equalizer. Test procedure: APA system was set up using a microphone, mixer, FBX,power
5SL820 & SM820 FRONT PANELSPOWERThe On/Off power switch is a two-position pushbutton switch. The LEDs corresponding to all activefilters will blin
6Recommended setting of the Clip Level Adjust:the clip LED should blink intermittently. NOTE: re-gardless of the Clip Level Adjust, setting Unity on t
7OUTPUT UNITY/LINE SWITCHSwitch to Unity (level in = level out) for standard line,insert, or guitar level applications. In the Unity setting,the SL820
8NOTE: Use a TRSconnector at bothends of cable.NOTE: Use aTRS connectoronly at the mixerinsert point.APPLICATIONSSL820: You can use the SL820 withacou
9Note for SM820: Use the SM820with balanced microphones.NOTE: An SL820 can be inserted at line level afterthe mixer and before the power amp on smalle
Comments to this Manuals